Outils pour utilisateurs
back2root:ibm-pc-ms-dos:hardware:8042
Différences
Ci-dessous, les différences entre deux révisions de la page.
| Les deux révisions précédentesRévision précédenteProchaine révision | Révision précédente | ||
| back2root:ibm-pc-ms-dos:hardware:8042 [2022/12/29 16:19] – [Keyboard Responses to System (via 8042 port 60h)] frater | back2root:ibm-pc-ms-dos:hardware:8042 [2024/08/27 15:38] (Version actuelle) – [Commands System Issues to Keyboard (write port 60h)] frater | ||
|---|---|---|---|
| Ligne 1: | Ligne 1: | ||
| - | ====== 8042 - Keyboard Controller | + | ====== 8042 - Keyboard Controller (AT,PS/2) ====== |
| - | ==== 8042 Commands & Responses ==== | + | ==== 8042 Commands & Responses |
| - | === Commands System Issues to Keyboard (via 8042 port 60h) === | + | === Commands System Issues to Keyboard (write port 60h) === |
| - | + | {{tablelayout? | |
| - | ^ Command | + | ^ Command |
| | EDh | Set/Reset Mode Indicators, keyboard responds with ACK then waits for a following option byte.\\ When the option byte is received the keyboard again ACK's and then sets the LED's accordingly.\\ Scanning is resumed if scanning was enabled. If another command is received instead of the option byte (high bit set on) this command is terminated. | | EDh | Set/Reset Mode Indicators, keyboard responds with ACK then waits for a following option byte.\\ When the option byte is received the keyboard again ACK's and then sets the LED's accordingly.\\ Scanning is resumed if scanning was enabled. If another command is received instead of the option byte (high bit set on) this command is terminated. | ||
| - | |7-3|2|1|0| Keyboard Status Indicator Option Byte | + | |7-3|2|1|0| Keyboard Status Indicator Option Byte |
| - | | + | | | | `--- Scroll-Lock indicator |
| - | | + | | | `---- Num-Lock indicator |
| - | | + | | `----- Caps-Lock indicator |
| - | | + | `------- reserved (must be zero) </ |
| - | </ | + | | EEh | Diagnostic Echo, keyboard echoes the EE byte back to the system without an acknowledgement. |
| - | | EEh | Diagnostic Echo, keyboard echoes the EE byte back to the system without an acknowledgement.| | + | | F0h | PS/2 Select/Read Alternate Scan Code Sets, instructs keyboard to use one of the three make/break scan code sets.\\ Keyboard responds by clearing the output buffer/ |
| - | | F0h | PS/2 Select/Read Alternate Scan Code Sets, instructs keyboard to use one of the three make/break scan code sets. Keyboard responds by clearing the output buffer/ | + | |
| - | | + | |
| - | | + | |
| - | | + | |
| - | | + | | F2h | PS/2 Read Keyboard ID, keyboard responds with an ACK and a two byte keyboard ID of 83AB. | |
| - | | F2h | PS/2 Read Keyboard ID, keyboard responds with an ACK and a two byte keyboard ID of 83AB.| | + | |
| | F3h | Set Typematic Rate/Delay, keyboard responds with ACK and waits for rate/delay byte.\\ Upon receipt of the rate/delay byte the keyboard responds with an ACK, then sets the new typematic values and scanning continues if scanning was enabled.< | | F3h | Set Typematic Rate/Delay, keyboard responds with ACK and waits for rate/delay byte.\\ Upon receipt of the rate/delay byte the keyboard responds with an ACK, then sets the new typematic values and scanning continues if scanning was enabled.< | ||
| - | | + | |7|6|5|4|3|2|1|0| |
| - | | + | | | | |-+-+-+-+---- typematic rate indicator (see INT 16,3) |
| - | | + | | | | | | `------- A in period formula (see below) |
| - | | + | | | | `---------- B is period formula (see below) |
| - | | + | | `------------- typematic delay |
| - | | + | `-------------- always zero |
| - | | F4h | Enable Keyboard, cause the keyboard to clear its output buffer and last typematic key and then respond with an ACK. The keyboard then begins scanning.| | + | </ |
| - | | F5h | Default w/Disable, resets keyboard to power-on condition by clearing the output buffer, resetting typematic rate/delay, resetting last typematic key and setting default key types. The keyboard responds with an ACK and waits for the next instruction.| | + | | F4h | Enable Keyboard, cause the keyboard to clear its output buffer and last typematic key and then respond with an ACK. The keyboard then begins scanning. |
| - | | F6h | Set Default, resets to power-on condition by clearing the output buffer, resetting typematic rate/delay and last typematic key and sets default key types. The keyboard responds with an ACK and continues scanning.| | + | | F5h | Default w/Disable, resets keyboard to power-on condition by clearing the output buffer, resetting typematic rate/delay, resetting last typematic key and setting default key types.\\ The keyboard responds with an ACK and waits for the next instruction. |
| - | | F7h | PS/2 Set All Keys to Typematic, keyboard responds by sending an ACK, clearing its output buffer and setting the key type to Typematic. Scanning continues if scanning was enabled. This command may be sent while using any Scan Code Set but only has effect when Scan Code Set 3 is in use.| | + | | F6h | Set Default, resets to power-on condition by clearing the output buffer, resetting typematic rate/delay and last typematic key and sets default key types.\\ The keyboard responds with an ACK and continues scanning. |
| - | | F8h | PS/2 Set All Keys to Make/Break, keyboard responds by sending an ACK, clearing its output buffer and setting the key type to Make/Break. Scanning continues if scanning was enabled. This command may be sent while using any Scan Code Set but only has effect when Scan Code Set 3 is in use.| | + | | F7h | PS/2 Set All Keys to Typematic, keyboard responds by sending an ACK, clearing its output buffer and setting the key type to Typematic.\\ Scanning continues if scanning was enabled. This command may be sent while using any Scan Code Set but only has effect when Scan Code Set 3 is in use. |
| - | | F9h | PS/2 Set All Keys to Make, keyboard responds by sending an ACK, clearing its output buffer and setting the key type to Make. Scanning continues if scanning was enabled.\\ This command may be sent while using any Scan Code Set but only has effect when Scan Code Set 3 is in use.| | + | | F8h | PS/2 Set All Keys to Make/Break, keyboard responds by sending an ACK, clearing its output buffer and setting the key type to Make/Break.\\ Scanning continues if scanning was enabled. This command may be sent while using any Scan Code Set but only has effect when Scan Code Set 3 is in use. |
| - | | FAh | PS/2 Set All Keys to Typematic Make/Break, keyboard responds by sending an ACK, clearing its output buffer and setting the key type to Typematic Make/ | + | | F9h | PS/2 Set All Keys to Make, keyboard responds by sending an ACK, clearing its output buffer and setting the key type to Make. Scanning continues if scanning was enabled.\\ This command may be sent while using any Scan Code Set but only has effect when Scan Code Set 3 is in use. |
| - | | FBh | PS/2 Set Key Type to Typematic, keyboard responds by sending an ACK, clearing its output buffer and then waiting for the key ID (make code from Scan Code Set 3).\\ The specified key type is then set to typematic.This command may be sent while using any Scan Code Set but only has effect when Scan Code Set 3 is in use.| | + | | FAh | PS/2 Set All Keys to Typematic Make/Break, keyboard responds by sending an ACK, clearing its output buffer and setting the key type to Typematic Make/Break.\\ Scanning continues if scanning was enabled.\\ This command may be sent while using any Scan Code Set but only has effect when Scan Code Set 3 is in use. |
| - | | FCh | PS/2 Set Key Type to Make/Break, keyboard responds by sending an ACK, clearing its output buffer and then waiting for the key ID (make code from Scan Code Set 3).\\ The specified key type is then set to Make/Break. This command may be sent while using any Scan Code Set but only has effect when Scan Code Set 3 is in use.| | + | | FBh | PS/2 Set Key Type to Typematic, keyboard responds by sending an ACK, clearing its output buffer and then waiting for the key ID (make code from Scan Code Set 3).\\ The specified key type is then set to typematic.This command may be sent while using any Scan Code Set but only has effect when Scan Code Set 3 is in use. | |
| - | | FDh | PS/2 Set Key Type to Make, keyboard responds by sending an ACK, clearing its output buffer and then waiting for the key ID (make code from Scan Code Set 3).\\ The specified key type is then set to Make.\\ This command may be sent while using any Scan Code Set but only has effect when Scan Code Set 3 is in use.| | + | | FCh | PS/2 Set Key Type to Make/Break, keyboard responds by sending an ACK, clearing its output buffer and then waiting for the key ID (make code from Scan Code Set 3).\\ The specified key type is then set to Make/Break. This command may be sent while using any Scan Code Set but only has effect when Scan Code Set 3 is in use. |
| - | | FEh | Resend, should be sent when a transmission error is detected from the keyboard| | + | | FDh | PS/2 Set Key Type to Make, keyboard responds by sending an ACK, clearing its output buffer and then waiting for the key ID (make code from Scan Code Set 3).\\ The specified key type is then set to Make.\\ This command may be sent while using any Scan Code Set but only has effect when Scan Code Set 3 is in use. |
| - | | FFh | Reset, Keyboard sends ACK and waits for system to receive it then begins a program reset and Basic Assurance Test (BAT). Keyboard returns a one byte completion code then sets default Scan Code Set 2.| | + | | FEh | Resend, should be sent when a transmission error is detected from the keyboard |
| + | | FFh | Reset, Keyboard sends ACK and waits for system to receive it then begins a program reset and Basic Assurance Test (BAT). | ||
| - | === Keyboard Responses to System (via 8042 port 60h) === | + | === Keyboard Responses to System (read port 60h) === |
| | 00h |Key Detection Error or Overrun Error for Scan Code Set 1, replaces last key in the keyboard buffer if the buffer is full. | | | 00h |Key Detection Error or Overrun Error for Scan Code Set 1, replaces last key in the keyboard buffer if the buffer is full. | | ||
| Ligne 54: | Ligne 54: | ||
| - | < | + | < |
| command F7h through FDh are NOP's on the AT and are ACK'ed but not acted upon | command F7h through FDh are NOP's on the AT and are ACK'ed but not acted upon | ||
| </ | </ | ||
| Ligne 60: | Ligne 60: | ||
| see [[back2root: | see [[back2root: | ||
| - | ==== 8042 Status Register | + | ===== 8042 - Speaker Controller & NMI (AT,PS/2) - Port 61h ===== |
| - | ^ Port ^ Mode ^ name ^Description^ | + | This register can be Write and Read |
| - | | 60h | read | + | |
| - | | 60h | write |data register. | + | ^ bit ^ Description |
| - | | 64h | read | + | | 0 | PIT Channel 2 enabled (see [[back2root: |
| - | | 64h | write |command register.| Writing this port sets Bit 3 of the status register to 1 and the byte is treated as a controller command. Devices attached to the 8042 should be disabled before issuing commands that return data since data in the output register will be overwritten.| | + | | 1 | Speaker Position\\ < |
| + | | 2 | | | ||
| + | | 3 | | | ||
| + | | 4 | | | ||
| + | | 5 | | | ||
| + | | 6 | | | ||
| + | | 7 | Reset Keyboard status (scan code readed) | ||
| + | |||
| + | === Speaker === | ||
| + | The speaker itself has two possible positions, " | ||
| + | |||
| + | This position can be set through bit 1 of port 0x61 on the Keyboard Controller. | ||
| + | |||
| + | If this bit is set (=1), the speaker will move to the " | ||
| + | |||
| + | Moving in and out repeatedly produces audible tones if the speed of repetition (the frequency) is within the range the speaker can reproduce and the human ear can hear. Also, a single movement in or out makes a click sound because it's so fast. Thus, a frequency which is too low to be heard as a tone may be heard as a rattle or buzz. (In fact, any frequency produced by this system also produces higher frequencies; | ||
| + | ==== 8042 Status Register (port 64h read) ==== | ||
| + | {{tablelayout? | ||
| + | ^ Port ^ Mode | ||
| + | | 60h | ||
| + | | 60h | ||
| + | | 64h | ||
| + | | 64h | ||
| ^ bit ^ Port 60h ^ Port 64h ^ 8042 Status Register | ^ bit ^ Port 60h ^ Port 64h ^ 8042 Status Register | ||
| Ligne 80: | Ligne 102: | ||
| ^ Command | ^ Command | ||
| - | | 20h | Read Command Byte: current 8042 command byte is placed in port 60h. | + | | 20h | Read Command Byte: current 8042 command byte is placed in port 60h.| |
| - | | 60h | Write 8042 Command Byte: next data byte written to port 60h is placed in 8042 command register. Format (see table 1) | | + | | 60h | Write 8042 Command Byte: next data byte written to port 60h is placed in 8042 command register. Format (see table 1)| |
| - | | A4h | Password Installed Test:\\ returned data can be read from port 60h;\\ < | + | | A4h | Password Installed Test:\\ returned data can be read from port 60h;\\ < |
| - | | A5h | Load Security: bytes written to port 60h will be read until a null (0) is found. | + | | A5h | Load Security: bytes written to port 60h will be read until a null (0) is found.| |
| - | | A6h | Enable Security: works only if a password is already loaded | + | | A6h | Enable Security: works only if a password is already loaded| |
| - | | A7h | Disable Auxiliary Interface: sets Bit 5 of command register stopping auxiliary I/O by driving the clock line low | | + | | A7h | Disable Auxiliary Interface: sets Bit 5 of command register stopping auxiliary I/O by driving the clock line low| |
| - | | A8h | Enable Auxiliary Interface: clears Bit 5 of command register | + | | A8h | Enable Auxiliary Interface: clears Bit 5 of command register| |
| | A9h | Auxiliary Interface Test: clock and data lines are tested; results placed at port 60h are listed below\\ < | | A9h | Auxiliary Interface Test: clock and data lines are tested; results placed at port 60h are listed below\\ < | ||
| - | | AAh | Self Test: diagnostic result placed at port 60h, 55h=OK | + | | AAh | Self Test: diagnostic result placed at port 60h, 55h=OK| |
| - | | ABh | Keyboard Interface Test:clock and data lines are tested; results placed at port 60h are listed above with command A9h | + | | ABh | Keyboard Interface Test:clock and data lines are tested; results placed at port 60h are listed above with command A9h| |
| - | | ACh | Diagnostic Dump: sends 16 bytes of 8042's RAM, current input port state, current output port state and 8042 program status word to port 60h in scan-code format. | + | | ACh | Diagnostic Dump: sends 16 bytes of 8042's RAM, current input port state, current output port state and 8042 program status word to port 60h in scan-code format.| |
| - | | ADh | Disable Keyboard Interface: sets Bit 4 of command register stopping keyboard I/O by driving the clock line low | | + | | ADh | Disable Keyboard Interface: sets Bit 4 of command register stopping keyboard I/O by driving the clock line low| |
| - | | AEh | Enable Keyboard Interface: clears Bit 4 of command register enabling keyboard interface. | + | | AEh | Enable Keyboard Interface: clears Bit 4 of command register enabling keyboard interface.| |
| - | | C0h | Read Input Port: data is read from its input port (which is inaccessible to the data bus) and written to output register at port 60h; \\ output register should be empty before call. (see Table 2) | + | | C0h | Read Input Port: data is read from its input port (which is inaccessible to the data bus) and written to output register at port 60h; \\ output register should be empty before call. (see Table 2)| |
| - | | C1h | Poll Input Port Low Bits: Bits 0-3 of port 1 placed in status Bits 4-7 | | + | | C1h | Poll Input Port Low Bits: Bits 0-3 of port 1 placed in status Bits 4-7| |
| - | | C2h | Poll Input Port High Bits: Bits 4-7 of port 1 placed in status Bits 4-7 | + | | C2h | Poll Input Port High Bits: Bits 4-7 of port 1 placed in status Bits 4-7| |
| - | | D0h | Read Output Port: data is read from 8042 output port (which is inaccessible to the data bus) and placed in output register; the output register should be empty. (see command D1 below) | + | | D0h | Read Output Port: data is read from 8042 output port (which is inaccessible to the data bus) and placed in output register; the output register should be empty. (see command D1 below)| |
| - | | D1h | Write Output Port: next byte written to port 60h is placed in the 8042 output port (which is inaccessible to the data bus) (see Table 3) | + | | D1h | Write Output Port: next byte written to port 60h is placed in the 8042 output port (which is inaccessible to the data bus) (see Table 3)| |
| - | | D2h | Write Keyboard Output Register: on PS/2 systems the next data byte written to port 60h input register is written to port 60h output register as if initiated by a device; invokes interrupt if enabled | + | | D2h | Write Keyboard Output Register: on PS/2 systems the next data byte written to port 60h input register is written to port 60h output register as if initiated by a device; invokes interrupt if enabled| |
| - | | D3h | Write Auxiliary Output Register: on PS/2 systems the next data byte written to port 60h input register is written to port 60h output register as if initiated by a device; invokes interrupt if enabled | + | | D3h | Write Auxiliary Output Register: on PS/2 systems the next data byte written to port 60h input register is written to port 60h output register as if initiated by a device; invokes interrupt if enabled| |
| - | | D4h | Write Auxiliary Device: on PS/2 systems the next data byte written to input register a port at 60h is sent to the auxiliary device | + | | D4h | Write Auxiliary Device: on PS/2 systems the next data byte written to input register a port at 60h is sent to the auxiliary device| |
| - | | E0h | Read Test Inputs: 8042 reads its T0 and T1 inputs; data is placed in output register; | + | | E0h | Read Test Inputs: 8042 reads its T0 and T1 inputs; data is placed in output register; |
| - | | Fxh | Pulse Output Port: Bits 0-3 of the 8042 output port can be pulsed low for 6 æs; Bits 0-3 of command indicate which Bits should be pulsed; 0=pulse, 1=don' | + | | Fxh | Pulse Output Port: Bits 0-3 of the 8042 output port can be pulsed low for 6 æs; Bits 0-3 of command indicate which Bits should be pulsed; 0=pulse, 1=don' |
| == Table 1 == | == Table 1 == | ||
| Ligne 140: | Ligne 161: | ||
| <WRAP round box> | <WRAP round box> | ||
| - | PC systems previous to the AT use the 8255 PPI as a keyboard controller and use the keyboard' | + | PC systems previous to the AT use the [[back2root: |
| the keyboard' | the keyboard' | ||
| </ | </ | ||
| - | see <A HREF=" | + | see KEYBOARD COMMANDS for information on programming the keyboards internal microprocessor |
back2root/ibm-pc-ms-dos/hardware/8042.1672327140.txt.gz · Dernière modification : 2022/12/29 16:19 de frater
Sauf mention contraire, le contenu de ce wiki est placé sous les termes de la licence suivante : CC Attribution-Noncommercial-Share Alike 4.0 International
